CAL45TB103K-1K [TAIYO YUDEN]
FIXED IND 10MH 45MA 155OHM TH;
| 型号： | CAL45TB103K-1K |
| 厂家： | 
TAIYO YUDEN (U.S.A.), INC |
| 描述： | FIXED IND 10MH 45MA 155OHM TH |
| 文件： | 总13页 (文件大小：789K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
[ For General Electronic Equipment
(General Environment) ]
Notice for TAIYO YUDEN Products
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2017. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully
before practical application or use of our products.
Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or
equipment incorporating our products, which are caused under the conditions other than those specified in this
catalog or individual product specification sheets.
■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification
sheets are available.
■ Please conduct validation and verification of our products in actual condition of mounting and operating
environment before using our products.
■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA
equipment, home electric appliances, office equipment, information and communication equipment including,
without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be
sure to contact TAIYO YUDEN for further information before using the products for any equipment which may
directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation,
automotive powertrain control system, train control system, and ship control system, traffic signal equipment,
disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information
network equipment including, without limitation, telephone exchange, and base station).
Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g.,
aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control
equipment, undersea equipment, military equipment).
*Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g.,
in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN.
Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment.
When our products are used even for high safety and/or reliability-required devices or circuits of general electronic
equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to
install a protection circuit as necessary.
Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way
responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog
for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above.
■ Information contained in this catalog is intended to convey examples of typical performances and/or applications
of our products and is not intended to make any warranty with respect to the intellectual property rights or any
other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights.
■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and
TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products.
Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in
accordance with such agreement.
■ The contents of this catalog are applicable to our products which are purchased from our sales offices or
authorized distributors (hereinafter“TAIYO YUDENs’official sales channel”). Please note that the contents of this
catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’s official sales
channel.
■ Caution for Export
Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export
Administration Regulations”,“Foreign Exchange and Foreign Trade Control Law”of Japan, and other applicable
regulations. Should you have any questions on this matter, please contact our sales staff.
1
AXIAL LEADED INDUCTORS
WAVE
■PARTS NUMBER
*Operating Temp. : -25～+105℃（Including self-generated heat）
△＝Blank space
△ △ △ △
C
A
L △
②
4
5
T
B
△
1
R
5
K
①
③
④
⑤
⑥
⑦
①Series name
⑤Nominal inductance
Code
CA
Series name
Code
（example）
1R5
Nominal inductance［μH］
High current axial leaded inductor
1.5
12
②Characteristics
120
Code
L△
Characteristics
Standard
※R＝Decimal point
⑥Inductance tolerance
Code
K
Inductance tolerance
±10％
③Dimensions（L×D）
Code
45
Dimensions（L×D）［mm］
8.0×4.4
⑦Internal code
Code
／
Internal code
Standard
④Lead configurations
△△△△
Code
TB
Lead configurations
Axial lead (52mm lead space)/ammo pack
Formed lead/ammo pack
VB
■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
Taping
Straight（TB）
Formed（VB）
φd
L
φD
52
(2.05)
5.0mm(0.197)
Standard quantity [pcs]
Taping
Type
L
φD
φd
Axial lead
Formed lead
8.0 max
4.4 max
0.65±0.05
CAL 45
2000
1500
（0.315 max）
（0.173 max）
（0.026±0.002）
Unit：mm（inch）
▶ꢀThisꢀcatalogꢀcontainsꢀtheꢀtypicalꢀspecificationꢀonlyꢀdueꢀtoꢀtheꢀlimitationꢀofꢀspace.ꢀꢀWhenꢀyouꢀconsiderꢀtheꢀpurchaseꢀofꢀourꢀproducts,ꢀpleaseꢀcheckꢀourꢀproductꢀspecificationꢀsheets.ꢀ
ꢀ
Forꢀdetailsꢀofꢀeachꢀproductꢀ(characteristicsꢀgraph,ꢀreliabilityꢀinformation,ꢀprecautionsꢀforꢀuse,ꢀandꢀsoꢀon),ꢀseeꢀourꢀwebsiteꢀ(http://www.ty-top.com/)ꢀ.ꢀ
1
106
■PARTS NUMBER
●CAL45
Rated currentꢀ※）ꢀ［ｍA］（max.）
Saturation current
Temperature rise current
Nominal inductance
［μH］
Measuring frequency
［MHz］
DC ResistanceDC
［Ω］（max.）
Parts number
EHS
Inductance tolerance
Idc2
Idc1
5600
5000
4400
4100
3900
3500
3100
3000
2800
2500
2200
2000
1700
1600
1400
1250
1200
1100
1000
920
890
790
700
620
590
550
490
420
370
350
320
290
270
250
240
220
190
170
150
140
130
110
100
95
CAL 45[] 1R0K
CAL 45[] 1R2K
CAL 45[] 1R5K
CAL 45[] 1R8K
CAL 45[] 2R2K
CAL 45[] 2R7K
CAL 45[] 3R3K
CAL 45[] 3R9K
CAL 45[] 4R7K
CAL 45[] 5R6K
CAL 45[] 6R8K
CAL 45[] 8R2K
CAL 45[] 100K
CAL 45[] 120K
CAL 45[] 150K
CAL 45[] 180K
CAL 45[] 220K
CAL 45[] 270K
CAL 45[] 330K
CAL 45[] 390K
CAL 45[] 470K
CAL 45[] 560K
CAL 45[] 680K
CAL 45[] 820K
CAL 45[] 101K
CAL 45[] 121K
CAL 45[] 151K
CAL 45[] 181K
CAL 45[] 221K
CAL 45[] 271K
CAL 45[] 331K
CAL 45[] 391K
CAL 45[] 471K
CAL 45[] 561K
CAL 45[] 681K
CAL 45[] 821K
CAL 45[] 102K
CAL 45[] 122K
CAL 45[] 152K
CAL 45[] 182K
CAL 45[] 222K
CAL 45[] 272K
CAL 45[] 332K
CAL 45[] 392K
CAL 45[] 472K
CAL 45[] 562K
CAL 45[] 682K
CAL 45[] 822K
CAL 45[] 103K
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
1.0
1.2
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
7.96
7.96
0.036
0.039
0.041
0.048
0.054
0.058
0.066
0.072
0.079
0.089
0.097
0.110
0.14
0.17
0.19
0.24
0.28
0.33
0.37
0.47
0.52
0.75
0.78
0.92
1.2
3300
3200
3000
2800
2700
2500
2400
2300
2200
2100
2000
1900
1800
1450
1430
1300
1220
1130
1080
900
870
710
700
640
630
490
470
450
425
355
330
280
240
240
220
210
170
150
140
120
110
90
1.5
7.96
1.8
7.96
2.2
7.96
2.7
7.96
3.3
7.96
3.9
7.96
4.7
7.96
5.6
7.96
6.8
7.96
8.2
7.96
10
2.52
12
2.52
15
2.52
18
2.52
22
2.52
27
2.52
33
2.52
39
2.52
47
2.52
56
2.52
／
68
2.52
82
2.52
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
10000
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.0796
1.6
1.8
2.3
2.9
3.4
3.6
4.9
6.3
7.0
7.8
11.0
13.2
17
22
27
36
45
65
75
69
70
80
90
65
90
90
60
100
125
155
80
60
75
50
65
45
・ [] Please specify the Lead configuration code.
※） The saturation current value (Idc1) is the DC current value having inductance decrease down to 10%. (at 20℃)
※） The temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃)
※） The rated current is the DC current value that satisfies both of current value saturation current value and temperature rise current value.
▶ꢀThisꢀcatalogꢀcontainsꢀtheꢀtypicalꢀspecificationꢀonlyꢀdueꢀtoꢀtheꢀlimitationꢀofꢀspace.ꢀꢀWhenꢀyouꢀconsiderꢀtheꢀpurchaseꢀofꢀourꢀproducts,ꢀpleaseꢀcheckꢀourꢀproductꢀspecificationꢀsheets.ꢀ
ꢀ
Forꢀdetailsꢀofꢀeachꢀproductꢀ(characteristicsꢀgraph,ꢀreliabilityꢀinformation,ꢀprecautionsꢀforꢀuse,ꢀandꢀsoꢀon),ꢀseeꢀourꢀwebsiteꢀ(http://www.ty-top.com/)ꢀ.ꢀ
1
107
AXIAL LEADED INDUCTORS
■PACKAGING
①Minimum Quantity
●Taping for Straight Leads
Type
Lead Configuration code
TB
Standard quantity [pcs]
2,000
CAL45
●Taping for Formed Leads
Type
Lead Configuration code
VB
Standard quantity [pcs]
1,500
CAL45
②Dimension
●CAL 45 TB（a：52mm lead space）
（2.05 inches）
Dimensions
Minimum insertion
pitch
Type
φD
L
a
b
|L1-L2|
1.0max
φd
4.4max
CAL45
8.0max
52＋2/－1
1.2max
0.65±0.05
10.0
（0.173max）
（0.315max）
（2.05＋0.079/－0.039）
（0.047max）
（0.039max）
（0.026±0.002）
（0.394）
Unit：mm（inch）
●CAL 45VB
Type
Symbol
D
Dimensions
φ4.4max
Symbol
P2
Dimensions
Symbol
Dimensions
※2
6.35±1.3
（0.250±0.051）
5.0±1.0
3.0max
W2
ℓ
（0.118max）
2.0max
14.0max
（0.551max）
16.0±1.0
H2
H0
P
F
△h
W
（0.197±0.039）
0.0±2.0
（0.079max）
φ4.0±0.2
D0
φd
L
（0.630±0.039）
12.7±1.0
（0.0±0.079）
18.0＋1.0/－0.5
（φ0.157±0.008）
φ0.65±0.05
（φ0.026±0.002）
11.0max
CAL 45
（0.500±0.039）
※1
12.7±0.3
（0.709＋0.039/－0.020）
12.5min
P0
P1
W0
W1
（0.500±0.012）
3.85±0.7
（0.492min）
（0.433max）
0.9max
9.0＋0.75/－0.5
（0.354＋0.030/－0.020）
t
（0.152±0.028）
（0.035max）
Unit：mm（inch）
※1 Accumulated error for 20 pitches is ± 1mm.
※2 Bonding tape must not protrude from the base tape.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_CA_pack_e-E02R01
AXIAL LEADED INDUCTORS（CAL Type）、
RADIAL LEADED INDUCTORS（LH Type）、
LEADED FERRITE BEAD INDUCTORS（ FB Series A Type／R Type）
■RELIABILITY DATA
1. Operating temperature Range
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
－25～＋ 105℃
CAL45 Type
LHL□□□
FBA/FBR
Test Methods and
Remarks
Including self-generated heat
2. Storage temperature Range
CAL45 Type
Specified Value
－40～＋ 85℃（Except for taping condition）
LHL□□□
FBA/FBR
3. Rated current
Specified Value
CAL45 Type
LHL□□□
FBA/FBR
Within the specified tolerance
CAL45 Type :
The maximum DC value having inductance within 10% and temperature increase within 40℃ by the application of DC bias.
LHL□□□ :
The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10：within 30%) and temperature increase within the
following specified temperature by the application of DC bias.
Test Methods and
Remarks
Reference temperature
: 25℃（LHL08, LHL10）
: 40℃（LHLC08, LHLC10）
FBA/FBR :
No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be
within ±20% of the initial value.
This is not guaranteed for electrical characteristics during current application.
4. Impedance
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
Within the specified tolerance
FBA/FBR :
Test Methods and
Remarks
Measuring equipment
Measuring frequency
: Impedance analyzer (HP4191A) or its equivalent
: Specified frequency
5. Inductance
CAL45 Type
LHL□□□
FBA/FBR
Within the specified tolerance
Specified Value
CAL45 Type :
Measuring equipment
Measuring frequency
LHL□□□ :
: LCR meter (HP4285A + HP42851A or its equivalent)
: Specified frequency
Test Methods and
Remarks
Measuring equipment
: LCR meter (HP4285A＋HP42851A or its equivalent)
: LCR meter (HP4263A) or its equivalent (at 1kHz)
: Specified frequency
Measuring frequency
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
6. Q
CAL45 Type
LHL□□□
FBA/FBR
Specified Value
Within the specified tolerance
LHL□□□
Test Methods and
Remarks
Measuring equipment
: LCR meter (HP4285A＋HP42851A or its equivalent)
: LCR meter (HP4263A) or its equivalent (at 1kHz)
: Specified frequency
Measuring frequency
7. DC Resistance
Specified Value
CAL45 Type
LHL□□□
FBA/FBR
Within the specified tolerance
Test Methods and
Remarks
Measuring equipment
: DC ohmmeter
8. Self resonance frequency
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
Within the specified tolerance
Test Methods and LHL□□□
Remarks
Measuring equipment
: (HP4191A, 4192A) its equivalent
9. Temperature characteristic
CAL45 Type
LHL□□□
FBA/FBR
Specified Value
△L/L : Within ±7%
Change of maximum inductance deviation in step 1 to 5
Temperature (℃)
Step
LHL□□□
1
2
3
4
5
20
Test Methods and
Remarks
Minimum operating temperature
20 (Standard temperature)
Maximum operating temperature
20
10. Tensile strength test
CAL45 Type
LHL□□□
FBA/FBR
Specified Value
No abnormality such as cut lead, or looseness.
CAL45 Type : Apply the stated tensile force progressively in the direction to draw terminal.
force (N)
10
duration (s)
10
LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal.
Test Methods and
Remarks
Nominal wire diameter tensile φd (mm)
0.3＜φd≦0.5
force (N)
duration (s)
5
0.5＜φd≦0.8
10
25
30±5
0.8＜φd≦1.2
FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the
of the component during 10±1 seconds.
axial direction
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
11. Over current
Specified Value
CAL45 Type
LHL□□□
FBA/FBR
No emission of smoke no firing.
There shall be no scorch or short of wire.
LHLC08, LHLC10 : There shall be no firing.
LHL□□□・CAL45 Type ：
Measuring current
Duration
Test Methods and
Remarks
: Rated current×2
: 5 min.
: one time
Number of measuring
12. Terminal strength : bending
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
No abnormality such as cut lead, or looseness.
CAL45 Type :
Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the
initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter
tensile
Mass reference
weight
Bending force
0.3＜ φ d≦0.5
0.5＜ φ d≦0.8
2.5
5
0.25
0.50
Test Methods and
Remarks
LHL□□□・FBA/FBR :
Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the
initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter
tensile
Mass reference
Bending force
weight
0.25
0.5
0.3＜φd≦0.5
0.5＜φd≦0.8
0.8＜φd≦1.2
2.5
5
10
1.0
13. Insulation resistance : between the terminals and body
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
100MΩmin.
LHL□□□ :
Applied voltage
Duration
Test Methods and
Remarks
: 500 VDC
: 60 sec.
14. Insulation resistance : between terminals and core
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
1MΩmin.
FBA/FBR :
Applied voltage
Duration
Test Methods and
Remarks
: 100 VDC
: 60±5 sec.
15. Withstanding : between the terminals and body
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
No abnormality such as insulation damage
LHL□□□ :
According to JIS C5101-1.
Metal global method
Test Methods and
Remarks
Applied voltage
Duration
: 500 VDC
: 60 sec.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
16. DC bias characteristic
CAL45 Type
△L/L : Within －10%
Specified Value
LHL□□□
FBA/FBR
Test Methods and
Remarks
CAL45 Type : Measure inductance with application of rated current using LCR meter to compare it with the initial value.
17. Body strength
Specified Value
CAL45 Type
LHL□□□
FBA/FBR
No abnormality as damage.
No abnormality such as cracks on body.
CAL45 Type :
Applied force
Duration
:50N
: 10 sec.
Speed
: Shall attain to specified force in 2 sec.
FBA :
Applied force : 50±3N
Duration : 30±1 sec.
Test Methods and
Remarks
18. Resistance to vibration
CAL45 Type
△L/L : Within ±5%
Appearance : No abnormality
△L/L : Within ±5%
LHL□□□
FBA/FBR
Specified Value
Q change : Within ±30%
Appearance : No abnormality
Impedance change : Within ±20%
CAL45 Type :
Directions
: 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range
Amplitude
: 10 to 55 to 10Hz (1min.)
: 1.5mm
Mounting method
Recovery
: Soldering onto printed board.
Test Methods and
Remarks
: At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□・FBA/FBR :
Directions
: 2 hrs each in X, Y and Z directions total : 6hrs.
: 10 to 55 to 10Hz (1min.)
: 1.5mm
Frequency range
Amplitude
Mounting method
: Soldering onto printed board.
19. Resistance to shock
CAL45 Type
No significant abnormality in appearance
Specified Value
LHL□□□
FBA/FBR
CAL45 Type :
Drop test
Test Methods and
Remarks
Impact material
Height
: concrete or vinyl tile
: 1m
Total number of drops
: 10 times
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
20. Solderability
Specified Value
CAL45 Type
LHL□□□
FBA/FBR
At least 75％ of terminal electrode is covered by new solder.
At least 75％ of terminal electrode is covered by new solder.
At least 90％ of terminal electrode is covered by new solder.
CAL45 Type :
Solder temperature
Duration
: 230±5℃
: 2±0.5 sec.
LHL□□□ :
Solder temperature
Duration
: 235±5℃
Test Methods and
Remarks
: 2±0.5 sec.
Immersion depth
FBA/FBR :
: Up to 1.5mm from bottom of case.
Solder temperature
Duration
: 230±5℃
: 3±1 sec.
Immersion depth
: Up to 1.5mm from terminal root.
21. Resistance to soldering heat
CAL45 Type
△L/L : Within ±5%
No significant abnormality in appearance
Inductance change : Within ±5%
Q change : Within ±30%
LHL□□□
Specified Value
No significant abnormality in appearance
Impedance change : Within ±20%
FBA/FBR
CAL45 Type :
Solder temperature
: 270±5℃
Duration
: 5±0.5 sec. One time
Immersed conditions
Recovery
: Inserted into substrate with t=1.6mm
: At least 1hr of recovery under the standard condition after the test, followed by the measurement within
2hrs.
LHL□□□ :
Solder bath method :
Solder temperature
Duration
: 260±5℃
: 10±1 sec.
: Up to 1.5mm from the bottom of case.
: 350±10℃ (At the tip of soldering iron)
: 5±1 sec.
Manual soldering :
Solder temperature
Duration
Test Methods and
Remarks
: Up to 1.5mm from the bottom of case.
: No excessive pressing shall be applied to terminals.
: 1 to 2hrs of recovery under the standard condition after the test.
Caution
Recovery
FBA/FBR :
Solder bath method:
Condition 1:
Solder temperature
Duration
: 260±5℃
: 10±1 sec.
Immersion depth
Solder temperature
Duration
: Up to 1.5mm from the terminal root.
: 350±5℃
: 3±1 sec.
Condition 2 :
Immersion depth
Recovery
: Up to 1.5mm from the terminal root.
: 3hrs of recovery under the standard condition after the test.
22. Resistance to solvent
CAL45 Type
Please avoid the ultrasonic cleaning of this product.
LHL□□□
FBA/FBR
Specified Value
No significant abnormality in appearance
Impedance change : Within ±20%
FBA/FBR :
Solvent temperature
Duration
: 20～25℃
: 30±5 sec.
: Acetone
Test Methods and
Remarks
Solvent type
Recovery
: 3hrs of recovery under the standard condition after the test.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
23. Thermal shock
Specified Value
CAL45 Type
LHL□□□
△L/L : Within ±10%
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30%
Appearance : No abnormality
FBA/FBR
Impedance change : Within ±20%
CAL45 Type：Conditions for 1cycle
Step
Temperature (℃)
－25＋0/－3
Duration (min.)
30±3
1
2
3
4
Room temperature
＋85＋2/－0
Within 3
30±3
Room temperature
Within 3
Number of cycles
Recovery
: 5 cycles
: At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the
measurement within 2hrs.
Test Methods and
Remarks
LHL□□□・FBA/FBR： According to JIS C60068-2-14.
Conditions for 1 cycle
Step
Temperature (℃)
Minimum operating temperature
Room temperature
Duration (min.)
30±3
1
2
3
4
Within 3
30±3
Maximum operating temperature
Room temperature
Within 3
Number of cycles
Recovery
: 10 cycles 〔LHL□□□〕
: 5 cycles (FBA/ FBR)
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 〔LHL□□□〕
: 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA/ FBR)
24. Damp heat
Specified Value
CAL45 Type
LHL□□□
△L/L : Within ±10%
Appearance：No abnormality
FBA/FBR
Impedance change：Within ±20%
CAL45 Type :
Temperature
Humidity
: 40±2℃
: 90～95%RH
Duration
: 1000 hrs
Test Methods and
Remarks
Recovery
FBA/FBR :
Temperature
Humidity
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
: 60±2℃
: 90～95%RH
: 1000 hrs
Duration
Recovery
: 3hrs of recovery under the standard condition after the removal from the test chamber.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
25. Loading under damp heat
CAL45 Type
△L/L : Within ±10%
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30%
Specified Value
LHL□□□
FBA/FBR
CAL45 Type :
Temperature
Humidity
: 40±2℃
: 90～95%RH
: 1000 hrs
Duration
Applied current
Recovery
: Rated current
Test Methods and
Remarks
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ :
Temperature
Humidity
: 40±2℃
: 90～95%RH
Duration
: 1000＋48/-0 hrs
Applied current
Recovery
: Rated current
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
26. Loading at high temperature
CAL45 Type
△L/L : Within ±10%
Specified Value
LHL□□□
FBA/FBR
CAL45 Type :
Temperature
Duration
: 85±2℃
Test Methods and
Remarks
: 1000 hrs
Applied current
Recovery
: Rated current
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
27. Low temperature life test
CAL45 Type
△L/L : Within ±10%
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30%
Specified Value
LHL□□□
FBA/FBR
CAL45 Type :
Temperature
Duration
: －25±2℃
: 1000 hrs
Test Methods and
Remarks
Recovery
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ :
Temperature
Duration
:－40±3℃
: 1000＋48/-0 hrs
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
28. High temperature life test
CAL45 Type
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30%
Specified Value
LHL□□□
FBA/FBR
LHL□□□ :
Temperature
Duration
Test Methods and
Remarks
: 105±2℃
: 1000＋48/-0 hrs
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
AXIAL LEADED INDUCTORS（CAL Type）、
RADIAL LEADED INDUCTORS（LH Type）、
LEADED FERRITE BEAD INDUCTORS（FB Series A Type／R Type）
■PRECAUTIONS
1. Circuit Design
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment,
telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical
Precautions
equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear
control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or
damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
◆Design
Precautions
1. Please design insertion pitches as matching to that of leads of the component on PCBs.
◆Design
Technical
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will
considerations
cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Considerations for automatic placement
◆Adjustment of mounting machine
Precautions
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
◆Adjustment of mounting machine
considerations
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire inductor in the flux during the soldering operation.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering
heat, soldering etc sufficiently.
Precautions
◆Recommended conditions for using a soldering iron:
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
◆Reflow soldering
1. As for reflow soldering, please contact our sales staff.
◆Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
Technical
considerations
◆Recommended conditions for using a soldering iron
If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade
the reliability of the products.
5. Cleaning
Precautions
◆Cleaning conditions
1. CAL type, LH type
Please do not do cleaning by a supersonic wave.
◆Cleaning conditions
Technical
considerations
1. CAL type, LH type,
If washing by supersonic waves, supersonic waves may deform products.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_prec_e-E02R01
6. Handling
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
2. LH type
Precautions
If inductors are dropped onto the floor or a hard surface they should not be used.
◆Packing
1. Please do not give the inductors any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading /
fragile item).
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
Technical
1. There is a case to be damaged by a mechanical shock.
2. LH type
considerations
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead wire could be deformed by a fall or an excessive shock.
7. Storage conditions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the
storage area should be controlled.
Recommended conditions
・Ambient temperature 0～40℃
Precautions
・Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may
decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
◆Storage
Technical
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes
and deterioration of taping/packaging materials may take place.
considerations
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_prec_e-E02R01
相关型号：
CAL45TB152K
General Purpose Inductor, 1500uH, 10%, 1 Element, Ferrite-Core, AXIAL LEADED
TAIYO YUDEN
©2020 ICPDF网 联系我们和版权申明